2000 lb Zinc-Plated Trailer Jack Foot Plate | GD-LF-AS002
Max Payload: 2000LBS
Description: Zinc Plated
2000 lb Zinc-Plated Trailer Jack Foot Plate with Short Receiver Tube
GD-LF-AS002 is a 2000 lb maximum-payload trailer jack foot plate with a published size of 18.5 × 9 × 10 cm and a zinc-plated surface.
The exact product image verifies a formed rectangular ground plate, a short round receiver tube welded to the plate, and a transverse retaining-pin assembly with a spring-style clip. Unlike GD-LF-AS001, this is a compact removable jack-foot architecture rather than a long adjustable drop leg.
2000 lb Is the Published Foot-Accessory Maximum Payload—not a New Rating for the Complete Trailer Jack
The supplied data states Max Payload: 2000 LBS. This page preserves that wording and does not relabel it as jack lift capacity, static support capacity or trailer GVWR. Installed system capacity remains governed by the lowest-rated relevant component and the actual mechanical fit.
A Short Receiver Tube Makes GD-LF-AS002 a True Footplate Rather than a Drop Leg
Current trailer-jack accessory catalogs use jack footorreplacement footplate for compact plate-and-receiver assemblies like this. The short tube connects the plate to the jack inner tube without creating the long extension geometry of a drop leg.
This makes GD-LF-AS002 a distinct sourcing option from GD-LF-AS001, which owns the adjustable drop-leg intent.
The Visible Pin Interface Defines Mechanical Compatibility with the Trailer Jack
The real image shows a transverse retaining pin through the receiver tube and a spring-style clip securing the pin. This is consistent with current removable 2,000 lb jack-foot products that attach to the jack inner tube through a pin-and-clip interface.
However, the current GD-LF-AS002 specification does not publish receiver-tube inside diameter, compatible jack tube diameter, pin diameter or hole-center dimensions. Those fit parameters remain production-drawing items.
18.5 × 9 × 10 cm Is Preserved Exactly as Supplied
The product brief gives 18.5 × 9 × 10 cm. The photograph is consistent with a compact rectangular footplate and short receiver assembly, but no dimensioned drawing defines which number corresponds to plate length, plate width or total assembly height.
For that reason, the page does not silently reassign those three values to individual geometric features.
The Formed Plate Provides a Broader Support Interface than the Jack Tube Alone
A foot plate spreads the jack reaction over a larger surface than a bare tube end. This can reduce local sinking on firm but somewhat compliant ground and provides a more stable contact interface for the trailer jack.
Ground bearing strength still matters. Soft mud, loose fill or unstable slopes can require an additional support pad or a different setup.
Zinc Plating Is the Published Finish for GD-LF-AS002
The supplied description identifies the surface treatment as Zinc Plated. Current 2,000 lb replacement trailer-jack footplates also commonly use zinc or clear-zinc finishes for corrosion resistance on exposed jack hardware.
No plating thickness, salt-spray duration, passivation type or marine corrosion classification is supplied for GD-LF-AS002.
A 2,000 lb Jack Still Needs the Correct Tube and Pin Geometry
Current removable jack feet are commonly specified by compatible inner-tube diameter and retaining-pin diameter. A matching 2,000 lb load class does not guarantee that the receiver tube will fit a particular jack.
Before publishing a compatibility list, confirm the GD-LF-AS002 receiver ID, intended jack tube OD, hole alignment and retaining-pin dimensions.
GD-LF-AS002 Data Boundary
Buyer Questions for the 2000 lb Foot Plate
Is GD-LF-AS002 a drop leg?
No. The exact image shows a short receiver tube attached to a compact rectangular plate. GD-LF-AS001 is the long adjustable drop-leg product.
What is the published maximum payload?
2000 lb. That figure is not automatically a lift or static-support rating for the complete jack.
What is the published size?
18.5 × 9 × 10 cm. Exact dimensional reference points should be confirmed from the production drawing.
Does the product use a retaining pin?
The exact product image visibly shows a transverse pin and spring-style retaining clip. Pin diameter and compatibility dimensions are not yet published.
Will it fit every 2,000 lb trailer jack?
No. Receiver-tube and pin geometry must match the jack.
Production Visibility for Trailer-Jack Accessories and OEM Programs
GOODIN supports B2B sourcing with real production, component-handling and workshop inspection visibility. Product-specific tube fit, retaining-pin geometry, weld criteria, load verification and plating requirements should still be confirmed against current production documentation.
Trademark Registration Across Key Markets
GOODIN maintains trademark registrations in multiple markets as part of its international brand and distribution presence.
Australia
United Kingdom
European UnionTrademark registration indicates brand ownership/registration status and does not constitute load certification, trailer-jack certification or regulatory approval for GD-LF-AS002.
Specify Jack-Tube Diameter and Retaining-Pin Geometry Before Confirming Compatibility
For quotation, provide trailer-jack model, jack inner-tube outside diameter, required receiver-tube inside diameter, pin diameter, hole location, desired foot dimensions, maximum payload requirement, zinc-plating specification, inspection criteria, quantity and destination market.
