2000 lb Sidewind Trailer Jack with 8 in Wheel | LF965-2010B

What Can Be Matched Directly from the Current Specification

The 10 in Stroke Is Consistent with the Published Height Difference—but the Datum Still Matters

The published 12.4 in bracket-height and 22.4 in extended-height values differ by exactly 10 in, matching the stated travel distance.

That consistency is useful during selection, but bracket height should still be matched using the same reference point shown on the LF965-2010B drawing rather than automatically relabelled as an overall retracted height.

GOODIN’sTrailer Jack Selection Guide provides broader guidance on capacity, travel and working-height matching.

Wheel Diameter Helps with Clearance and Surface Matching—not with Inventing a Moving-Load Rating

The current specification confirms an 8 in wheel diameter. It does not state wheel count, wheel material, width, tyre construction, bearing design or an allowable load while the trailer is rolling.

The jack’s 2,000 lb capacity therefore should not be used as a dynamic manoeuvring rating for the wheel assembly. Surface condition and the actual load carried at the jack position remain separate checks.

Do Not Treat LF965-2010B and LF965-2010BS as Automatic Substitutes

Shared height and finish fields do not prove identical wheel or mounting assemblies. Use the exact model drawing and current product image for replacement approval.

Keep the Outer and Inner Tube Finishes Separate in the Purchasing Specification

LF965-2010B specifies black powder coating on the outer tube and zinc plating on the inner tube. The two surfaces should not be collapsed into a generic “coated steel” description.

For projects with defined corrosion exposure, GOODIN’s corrosion-resistant trailer hardware guide provides broader context on turning a finish name into a measurable environmental requirement.

Confirm the Wheel Assembly and Mount Before Bulk or Replacement Approval

The published brief is sufficient to compare capacity, Sidewind operation, travel, wheel diameter, height references and tube finishes. Wheel count, mounting architecture and hardware still require LF965-2010B-specific imagery or drawing evidence.

Questions to Resolve Before Ordering LF965-2010B

Production Visibility for OEM and Distributor Buyers

Wheel-Equipped Trailer Support Where 2,000 lb Capacity and a 12.4–22.4 in Height Window Fit

LF965-2010B is intended for compatible trailer applications where the actual load at the jack position fits the published capacity and the 10 in adjustment range matches the coupling and parked-support geometry.

Final application approval should also confirm the actual wheel assembly, mounting interface and Sidewind clearance.

Match the 8 in Wheel to the Floor, Thresholds and Real Manoeuvring Requirement

An 8 in diameter can be useful when checking ground clearance and threshold geometry, but wheel diameter alone does not define rolling resistance or manoeuvring load.

GOODIN’s guide to moving a boat trailer in a tight garage provides practical context for smooth floors, rough surfaces, thresholds, turning space and low-speed trailer positioning.

Check Both Ends of the Published Height Range Against the Trailer

Use the 12.4 in bracket-height reference and 22.4 in extended value against the actual trailer geometry. The 10 in travel value alone is not enough to approve a replacement if the mounting datum is different.

Reserve Lateral Crank Space at the Installed Position

Toolboxes, couplers, winches, guards and body panels can interfere with a Sidewind crank. Handle radius is not supplied, so verify the real operating arc on the LF965-2010B assembly or drawing.

Use Actual Jack-Position Load—not Trailer GVWR or Wheel Diameter—as the Capacity Input

The current brief does not split lift and support capacity. Confirm the vertical load carried at the jack position and keep wheel/manoeuvring limits separate from the jack’s published 2,000 lb rating.

Define Corrosion Performance Separately for Wet or Salt-Exposed Applications

Black powder coat on the outer tube and zinc plating on the inner tube are the confirmed finish descriptions. If coating thickness, passivation or salt-spray acceptance is contractual, add those values to the purchasing specification.

Do not approve LF965-2010B by matching only the LF965 family name and 12.4–22.4 in dimensions. Confirm capacity, wheel assembly, mounting interface and crank/stowage clearance on the exact model.

What to Send with the LF965-2010B RFQ

Provide actual vertical load at the jack position, trailer/frame drawing, mounting method, required minimum/maximum support positions, wheel-count and wheel-construction requirement, intended surface, Sidewind clearance, corrosion specification, quantity and destination market.